Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
We have a customer interest in developing a BlueZ application using the nRF52840.
This will be using the ARM9 CPU Atmel SAM9G25.
These are some of the software versions...
Environment introduction:
1. Use software SEGGER Embedded Studio for ARM (Nordic Edition) V5.50a.
2. 52833-DK*3 And EK42442ds *2
3. Switch order ANT1>ANT2>ANT3>ANT4...
Hello Group,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I was...
Hello there!
We have different sensors connected to our custom nRF52840-based board running Zephyr OS. The goal is to transfer sensor readings to the PC by using a USB link...
The problem I encounter now is that NRF52840 is my MCU, and I need RS485 module to transmit data. The supply voltage of my NRF52840 is 1.8V. Is it recommended that the RS485...
Hello,
I am trying to do a single bank DFU update using nRF Connect app and have SDK 16 on my device. I have set NRF_DFU_SINGLE_BANK_APP_UPDATES to 1. Bot looking at postvalidate...
Using the NRF5 SDK V17.0.2
Once again finding myself struggling to understand the structure of the SDK as a result of lacking documentation, there seem to be so many layers...
I have a working project developed against nRF Connect SDK version 1.6.1. I am attempting to update to version 1.9.1 nRF Connect SDK as a stepping stone to v2.0.0. Upon further...
Hi Nordic,
Currently, I am using:
- nRF5 SDK 17.1.0
- nRF52833-DK
- pca10100
You can download "my_projects" file from here . It should be put under "examples" directory...
Hi people,
I would like to know how to use the I2C of my thingy:53.
Since there is a Qwiic connector I want to know if it is possible to connect to a Qwiic display,...
Hi,
I am experiencing difficulties directing shell to both RTT and UART backend simultaneously for ncs v1.8.0. UART stops outputting while RTT is disconnected and only seems...
Hi,
¿Is it possible to install same tools for building a zephyr project that nRF Connect installs, in a linux without graphic interface?
I tried manually installing zephyr...
I want to enable a timer to start SAADC Multiple Channel and get value of each channel after every 1 seconds.
There are many questions on how to enable a timer to start...
Hi,
I'm using a custom board to record i2s data to a sd card. The recording starts and stops on a button press (Pin 25), which basically works. My problem is that the...
Hi,
I'm using a nRF52 DK (nRF52832) and nRF5 SDK 17.0.1. to read data from an external ADC via I2S. I can read some data from the I2S bus, but I'm confused about the bit...
