Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I have a Jtrace which I use over ethernet.
Running nrfjprog shows:
nrfjprog -f nrf52 --eraseall ERROR: No debuggers were discovered. NOTE: For additional output, try running...
hello, im using nRF52840, pca10056, I was using the example ble uart from examples\peripheral\uart im planning on replacing the use of "putty" PC application with a program...
Hello, i did my own custom board with a nrf52805 and now I did one custom first she is working fine so I decided to do the same but I can't see my device in nrf connect app...
Based on the "system_off" example, I intend to use the RTC to wake the device up (a NRF52840) periodically every minute.
I setup the RTC with LFCLK (32KHz) to trigger a...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Hello,
I am trying UDP sample with a local SIM (Orange) to check eDRX settings following this ticket .
Carrier said i should set an APN. This was not needed with 1NCE...
I try the new save to CSV feature in v3.4 power profiler.
I try to save all, but it says 0MB.
The sample rate is 100ksps, and duration is 301 seconds, but would result...
Hi, I have the following code in main.c:
If I initialize the beacon advertising first, which is the shown configuration, I get fatal error code 8 out of ble_advertising_start...
I have recently updated the SDK for my application from version 13.0.0 to 17.1.0, everything seems to be in order except for this function in nrf_drv_twi.c called twi_clear_bus...
the updated version of nRF connect v3.8 , for desktop , app - programmer doesnt recognize the device . i downgraded to 3.3v this version selects my device .
Hello,
I have developed a Thread network based on SDK for Thread & Zigbee v.4.1.0 and OTBR image provided by Nordic. I recently upgraded my OTBR from a Raspberry Pi 3B+...
Hi, I have added libuarte example in-app template and sent data from Arduino to nRF52840 successfully. But after receiving some data and I am getting the following error....
Hi,
I use nrf5340 and have issue with i2c large buffer send: In order to flash page to bootloader with my application:
I defined
I defined static array with size...
Hello !
If I understand right and nrf_crypto is the main Crypto API in nRF SDK. They can be mapped to cc310 or to mbedtls sw routines.
Does exists nrf_crypto asynchronous...
