Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi Support,
I am observing something that is quite strange on the GPIO input. I am developing a Zigbee device with Energy harvester with NRF52840. I need to use the state...
In addition to uarts, I2cs and SPIs I tried toggling some apparently spare pins without seeing voltage changes on the pins I tried.
Which pins are available for digital...
I'm using the Nordic nRF52840-DK board to breadboard an SDHC card interface in Zephyr using SPI. I have it doing "basic" operations, but am trying to reconcile what I'm physically...
Chip - BT832AF (nRF52810 QFAA)
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
2V- power supply
My application need not to be very fast, but is extremely concerned...
Hi,
I am working on a project with 2 nrf52840 devices. One is the nrf52840 dk, while the other is a custom board with the nrf52840 module. I want to perform a dfu over uart...
I think this is a very weird requirement
Normally , I use manufacturer data to do this like picture below
it's easy and quick
but it contains len and type occupying...
Hey,
I am trying to get the Asset_tracker_v2 running on my Thingy:91, but with my own Cloud connection (It is a Thingsboard CE hosted on an ubuntu Server in Open Telekom...
I have to execute some lightweight error correction codes (ideally BCH) to compare and subsequently correct the mismatches between two binary arrays. I am working on the nrf52840...
I have been testing lte_lc_init_and_connect with my units inside a Faraday cage, This method doesn't terminate when it cannot get a signal (at least I haven't seen it). This...
I am attempting to install the nRF Connect SDK v1.5.0 on Mac OS X Big Sur, I have followed the Getting Started Assistant and Toolchain Manager with no success.
Here is my...
Hello everyone,
I am going to Integrate Bluetooth mesh into the nRF5 SDK example by using SDK 17.0.2 and SDK for Mesh V.5. I followed the instruction mentioned on the Infocenter...
I am from India. Recently I have purchased Thingy91. I have registered IBasis SIM as mentioned in the user guide. While registering the device in the nrf cloud I am facing...
Kind folks,
Attempting to install the Nordic Connect SDK again after failing several times before. (Always seem to have something slightly wrong in my installation which...
Is it possible to have 2 timers (TIMER3 and TIMER4) with the exact timer value?
I need to have two gpios toggeling at a difference time frequency but based on the same clock...
