Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
Thanks for the help. I have run the proximity detection application in nRF52832 nordic thingy. Initially the LED was blinking in the thingy board but when I switched...
Hi,
Though the Thread CLI sample's 'README.rst' lists the following supported optional extensions, it does not specifically describe how to set the specific '.conf' files...
Hi everyone, Lately I have been using a PCA10040 (nRF52-DK) with J-Link OB-SAM3U128-V2-NordicSem V1.00 version. I'm trying to program two boards one with nRF51822_xxAA and...
Hi I am wondering what the best way to go about developing a RPi based system for presence detection with nordic ble devices
I would like to limit the bluetooth signal to...
Hello,
We are looking to do OTA device firmware update by GSM for the nRF52840.
We have a custom board with a nRF52840 and a GSM/LTE-M modem. They are communicating together...
SDK: 14.1.0
CHIP: nRF52840
CONFIG: ZIGBEE&BLE MULTI PROTOCOL
I wants to keep store zigbee pairing data after reset.
I setups like this.
After joining procedure...
From the gnss_extension.rst documentation shown below, it appears as thought the GNSS receiver can retain solution information from previous fixes/tracking in order to speed...
Hello Nordic!
I'm starting to develop my own Zigbee device with the nrf52840DK and I need to send some attributes to my coordinator, initially the door lock status is enough...
I am currently using an external JLINK to program the 9160 module, after adding read protection. Unable to recover using nrfjprog, report the following error:
ERROR: Recover...
Is there a version of the nRF Commandline tools that will run on an embedded Linux (ARM, RasberryPi compatible)? I specifically need the nrfjprog tool. The Segger tools do...
The v1.3 Product Specification datasheet for the nRF52833 lists the maximum source resistance on VBUS, including cable, as 2 ohms. Yet the same document recommends using a...
Hi,
As part of my internship, I am trying to modify an application and send the output of the application via CoAP. My goal is to modify the CoAP Client sample that comes...
Good morning, this is my first approach to nRF Connect and, even if 70 YO, I'm a beginner.
I've been able to read/flash/restore my DWM1001-dev using nFR Connect desktop...
Hi Nordic team,
" Cryptography library - nrf_crypto " section in SDK v17 online document explains pretty much crypto algorithms which are available on crypto-backend. It...
I'm working in migration from nRF51 to nRF52 and nrfx drivers. But now stucking in the errors. There are much errors, but all of that seem to be simulaly caused by the no...
