I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
I just got a ppk2 and I am not sure which wire needs to be connected to where.
I am going to use this to measure current consumption but I've used only extarnal DUT...
Hi all,
I'm starting a project with a nRF52840, and start protoyping with pca10056 board.
I started with compiling ble_app_blinky example app, with armgcc.
I can compile...
My nRF52 device has a connection opened in peripheral mode and in some cases I want to close the connection with reason code "power off", i.e. call sd_ble_gap_disconnect with...
Hi,
I'm reading through the documentation on using the SAADC with the NRF52 kits. The examples are using PPI to manage the SAADC and allow it to sample locationally in...
Dear All,
I need a high frequency clock in order to measure the time between a couple of events. In the RTC HAL there are functions that allow to retrieve the counter...
nordic nrfconnect sdk, wrong bit mask in driver for thingy light sensor bh1749
In the nordic nrfconnect sdk there is a bitmask typo causing wrong anction.
The header...
When running firmware without a probe, interrupts don't seem to work. I'm using a Segger Mini Edu on an Actinius Icarus (nRF9160). I'm using EGU1. When the probe is attached...
Hi,
I am looking for detailed electrical characterization details for SAADC - beyond 1 page summary in nRF52833 product spec v1.3; under 6.21.10.1 SAADC electrical specification...
Is there some documentation listing what C library functions are supported? For example if I use the Keil IDE to look for FILE I find it. But if I look for 'fread' it says...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
Hi,
I am using nRF52832 and SDK v15.00 for development.
I am working in ble_app_uart peripheral example. I have a task where I need to configure another UART communication...
Hello Everyone,
we are using Nordic's nRF52840 controller with SoftDevice S140 and the default Bootloader(C:\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble...
Hello, I am working on a nRF52840 and started with the SDK15 gls bonding example. The device has no buttons or display so we are stuck with 1v2. We are hoping to incorporate...
