Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hello,
I have used for my application the reference design of NRF52832.
The connector MURATA MM8130-2600 is used to have the choice between the PCB antenna and an external...
I have refer to this topic for setup multilink with NUS. https://devzone.nordicsemi.com/f/nordic-q-a/18804/mismatch-between-connection-handles-in-ble_nus
But, i met a wrong...
Hi Nordic,
While testing USB CDC example with nRF 15.3.0 in PDK board, I see USB is not recognized. I have gone through the same issue posted in Forum. Is it the issue with...
I have a question about “BLE_HCI_CONN_INTERVAL_UNACCEPTABLE”.
SDK: 15.3.0 Example: ble_app_multirole_lesc (source changed from sample) Device: EYSHJNZWZ (nRF52832)
The...
This microcontroller is advertised as mbed enabled. Does that mean that it can be easily programmed using mbed api in an mbed environment. I want to work in a c++ environment...
I am trying to use the nRF52-Development kit with (N52832) and using nRF5_SDK_15.0.0. What my application is to broadcast an iBeacon Packet (with Major, Minor, RSSI and UUID...
Hi,
I followed this tutorial ( https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/merging-two-ble-examples-together ) of combining UART example with other...
Hello. I use nrf52832 on Adafruit Feather board among with nrf5 SDK. As a default I can log any info via NRF_LOG_DEBUG to my serial monitor. But how can I use Serial input...
I was wondering if the standalone nRF51822 microcontroller has support for i2c. If so which pins are supported. There doesn't seem to be any reference on i2c for the board...
Hi,
I bought a custom nrf52840 board and I need to program my firmware on this SOC with PCA10056 DK debug output port. in below you can see part of shematic of my custom...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
Sir
about the
while(1)
{
sd_app_event_wait(); //stay here until a interrupt or connection occurs...
}
During the time that there is not a interrupt and no connections...
Hi,
I've recently switched some prototype code from using MQTT to a custom UDP-based protocol. What I noticed is that if I have the unit sleep for longer periods of time...
