Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi,
to what impedance shall the BT antenna be matched?
Copying from the datasheet:
A matching network is needed between the RF pin ANT and the antenna, to match the...
Requests for the FW:
Add characteristic to access general GPIO pins in analog and digital form.
extension of the existing MOS_1-4 access, PIN read/write under the...
Hi,
We use nrf51 SDK v9. I found there are two SER_MAX_CONNECTIONS defined both in app_ble_gap_sec_keys.h and ser_config.h. Their values are different. One is referred...
Hello,
I have a problem when I try to use cheaper Android phones to communicate with our 52832 chip.
I can discover the peripheral and then connect, but when I device...
Hi,
I flashed softdevice and ble_app_UART_c code. But after searching bt device, i could not find bt nrf52 device in mobile.
Do i need to something more..
hi,
i am using nrf52840. with sdk 14.1. i am trying to broadcast my dk as beacon. with your neccessary examples. i have created my own services and started advertising. when...
I want to transfer data using UART to BLE by Baud Rate 460800 up to(using nRF52832).
I need to send a file, its size is 100MBytes
However, the use of examples(14.0vesion...
I would like to establish a BLE unencrypted link to send text messages. I have nRF52480, nRF51 USB dongle, and a mobile phone. I run Ubuntu 14.04 and Win10. It is not clear...
Is it possible to program the Atmel SAM D20E chip (based on an ARM-M0 cortex processor) externally using the P19 debug out header on the nRF51-DK?
Thanks.
I am trying to understand the Passkey LESC pairing on S140 soft device using the latest SDK 14.0.2.
The message sequence charts has a block "App starts DHKey calculation...
Hi developer, sorry to interrupt and ask. How to use an ultrasonic sensor with nRF52? Since I search a code for nRF52 are not exist and see ultrasonic sensor can connect with...
I modified TWI_SENSOR_PCA10040 example from 14.10 SDK to run on my NRF52832 device, and it reads from the device address perfectly. However when I wrap reading inside a FreeRTOS...
Hello ,
What is the preferable way to flash code into NRF52832 IC during mass production? Flashing the code into custom IC with NRF52-DK in time consuming process.
And...
Hi,
All of a sudden (isn't it always the case :) the JLink debugger fails to flash the app code to the dev kit (PCA100028)
The Project's softdevice is flashing well without...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
