I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi all,
I am hoping to eventually integrate the crashlog functionality, but prior to this, I wanted to test the basic functionality with the flashlog. I have looked through...
Hi,
I'm currently working on getting LTE to work on our custom card, featuring an nRF9161 and an MFF2 eSIM (without PIN), but I can't seem to initialize our eSIM. I have...
Hi,
I know this issue has been addressed in other posts but none of the solutions tested worked for me. I tried the solution of this post : Intellisense stops working when...
hw: nRF9160-DK, v1.1.0
Using the McuBoot-Loader of NCS 2.5.1 and the NCS 2.6.1 zephyr dfu module seems to be not longer aligned with it.
A app using NCS 2.5.1 zephyr's...
We are developing Matter/Thread based Smart Lock product. One of the product requirements is that the product should be able to connect to a BLE mobile APP at all times i...
Hi,
The CPU temperature module is located in the network CPU in the case of nRF5340. I have read this thread : Zephyr API to read the nRF5340 die temperature - Nordic Q&A...
Hello,
we use nrf5340 with Connect SDK v2.0.0 and we have adopted rules for indicating the update process and the operation of the bootloader in the device. Therefore, I...
I am working with the Ebyte e83 Dev board and Also got the ARM-JTAG programmer.
I have been trying to follow the nrf connect for VS code series and seems to get stuck on...
Before I got a white screen after selecting a ble chip (52840 dongle in my case), I deleted my folders home/ (.config/nrfconnect .config/nrfconnect-bluetooth-low-energy, ...
I just migrated from MacBook Air with M1 processor to MacBook Pro with M3 processor. I installed VS Code and nRF Connect SDK v2.6.0 from scratch on my MacBook Pro. hough my...
Hi，
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Greetings team,
We are using the nRF Connect for Desktop v4.4.1 and Programmer tool has been updated to v4.3.0
Using this version the MCUBOOT settings are unable to turn...
Hello, I try to config vendor id and product id according to https://docs.nordicsemi.com/bundle/ncs-2.0.2/page/nrf/ug_matter_configuring_protocol.html .
1) When I change...
Good morning,
I work with the nRF52840DK board and the BC840E and I would need to make some changes to the SW of the "radio_test" application, but trying it out I find it...
Hi,
I am going to consider NRF52811-CAAA in a design. Can you please help with these questions:
1- What is the expected End of Life for NRF52811-CAAA chip?
2- If I have...
