Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi. I'm working on a BLE system with Central and Peripheral with nRF5340 with 70msec of CONN_INTERVAL and about 1sec of SUP_TIMEOUT. The Central unit also has a UART that...
HI
In the RF_Test example, there are 80 channels.
However, BLE has only 40 actual channels.
Why are there 40 channels...? I would like to know.
Do 80 channels...
Hi,
I am new to the NRF and private-public key pair using.
Can anyone please explain me how to use custom keys for MCUBoot, I added below config in /child_image/mcuboot...
Hi all
We are using ztest in our project because it works nicely together with twister, Zephyr's test runner tool. We need to have the ability to mock modules. For this...
Hi Team
we have NR52833 ,NRF52 these boards Serial no : 10001208 , 10001220
we use these devices in wipro BQTF as reference devices and not for any production. We are...
Hi
I read this Q&A: How to configure the P0.00 and P0.01 pins as GPIO , which is similar to my question. There are some things I did not get from that section:
"Physically...
Hi there, I am trying to do a blocking simple ADC measurement in using NRFX drivers in a threaded context, however when I build I get the following error:
gen_isr_tables...
Hi,
I am using nRF9160DK v0.9.0 with Cellular Monitor 2.4.0, and I have flashed AssetTracker2 via the "Program device" button.
Although asset tracker works fine uploafing...
Hi,
Using the nrf Connect Programmamer v4.2.0, I get the following error when connecting to J-Link on some of my custom boards (about 30%):
When I run nrfjprog...
I am attempting to enter a sleep state (System Off) with a wakeup button . I set all of my GPIO pins to the default config except for my wake up, configure the appropriate...
Hi
I am unable to get the Guiconfg to work in lesson 1 exercise 2 of the nRF Connect SDK Intermediate course.
I have attached snap shots of the output when I try to run...
I'm using the custom board of nrf 5340 with 7002.
When I run the sample project of Hello World, the current is about 90 ma,
and I run the sample project of WI-FI Scan...
We are going into sleep mode for the processor. We are using Zephyr and sdk 2.3. We also are keeping a running count of seconds and synching that once a day with a modem....
Hello,
I'm working on a product using the nRF9160 and facing challenges with poor LTE signal strength, leading to significant power drain when the device goes offline. I...
