Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
