I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
hello everybody,
i've downloaded the firmware files of nRF51822 beacon, but i couldn't find the source code. Does anybody know where i could find the source code of nrf51822...
Hello,
i try to use the nrfConnect (PC version) to update my devices via DFU. The DFU service is running on the device (update with Andoid nrfToolbox works without any...
Hi,
After finding that Windows doesn't like HID devices if they can't be bonded to, I've been attempting to add peer_manager and bonding into my application.
However...
Hi,
I'm working on a Custom Android app which connect to my NRF52 without any security.
This App is based on the UART demo App for Android, but I want that only my App...
