Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi,
I am trying to use the nRF915-DK with a GNSS Tracker application. Everything works fine, but, I am not able to set the nRF9151-DK properly for utilizing the board...
Hello
I'm preparing the certification RF testing software on our product 4MOD9192 using nRF7001 for wifi function.
During the certification test process, we need to...
Is it possible to add custom regions for a project to be used by the Partition Manager? I see how and where regions are defined, as shown here , but I'd like to use multiple...
I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core.
I would like to do Wi-Fi positioning with the nrf9151dk...
Hello,
I am using the nRF52833 - DK and running the USB CDC ACM example. I can transmit and receive data with the example. I noticed that when receiving data I am only able...
I am using Zephyr 3.7.0 with the Nordic-provided low level link layer (LLL) code on an nRF52840-DK. I'd like to set a breakpoint on rp_comm_rx_decode() ( https://github.com...
I want to connect two nRF54L15 development boards using I2C protocol. Is there any sample in nordic SDK v2.0.8 or v2.0.9 that I will help me to set up nRF54L15 DK as a master...
Hello,
To preface:
HW: nRF9151DK
SDK/Toolchain: nRF Connect SDK v2.9.0
I am new to Zephyr (first project)
When using a nRF91 modem, it seems that CONFIG_POSIX_API...
Hi there,
I would like to get information regarding the possibility of implementing 5.1 isochronous audio streams on the nRF5340 Audio DK development kit. According to this...
I've been using the function nrf_ble_scan_filter_set for several years with developmental hardware based on the ble_uart_c example, so I've reviewed that example thoroughly...
Hello,
I'm not able to sniff BLE using your tool
I tried to configure nrf sniffer with nrfutil.
OS: MacOS 15.1.1 (arm)
Wireshark: 4.0.17 (it seems the actual version...
Hello
Is is possible to enable MCUBoot image compression on nRF52832 ?
I tried to enable it following this blog post but I got a compilation error :
Compiler insulted...
I am using peripheral_uart as my base project. Right now MTU value is 23 I believe as I can receive only 20 bytes of data at a time. How I can increase the MTU size with configurations...
Hello,
in use is the nrf connect sdk v2.6.2 toolchain v2.6.2 on my nrf5340DK
I struggle transmitting ADC data from my nrf5340DK via USB to my windows PC. On my PC there...
