Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hi teams,
I am developing with Mesh SDK 4.0.0, and suffers from random fault during long-term test.
The last readable callstack position is the below.
The callstack...
I am currently trying to use a nordic semi ppk and nrf52840 to read current in the nordic semi power profiler software. I am able to flash the DK successfully (while P22 is...
I have a 9160 DK board with lte_ble_gateway on the 9160 side and hci_lpuart on the 52840 side. It works as far as being able to send and receive BLE messages but it has faults...
Hello,
Previous revisions of the nRF SoC's such as nRF52840 and nRF52832 have had specifications for certain IO to be low frequency < 10Khz and standard drive only because...
Hello
I'm facing an issue with app_timer_start. Indeed, with small values, sometimes, the app_timer_start won't start the timer. As a result, the interrupt handler is not...
Online Manlio 6 minutes ago
Hi,
I add NFC to my project with freertos. The initialization of nfc is ok. After running few seconds ,it hang. If I comment the usr_nfc_init...
Hello,
I work with the ATE using Algocraft WN series programmer.
It has directly access to GPIO registers through SWD interface with WRITE / READ / COMPARE commands. ...
Hi,
I was tracking down a bug that resulted in a secure fault exception. To save some time tracking it down I enabled logging in the spm. However this resulted in an escalated...
Hello,
So I am just real confused on how the softdevice programming works via the open_bootloader right now and can't seem to track down the documentation I need to be successful...
I'm running a code based on the ble_app_uart example using the PCA10059 dongle. I have the dongle connecting to a raspberry pi 0 W via BLE and when this runs using a power...
Hello,
at the moment I am working on a project with a nRF52840DK as central and multiple nRF52DKs as peripherals. The code on the central is based on the "ble_app_uart_c...
Do the examples in the SDK folder like ble_nus have their binaries with softdevice already? I'm a newbie in Nordic and using the BLE NUS example with nRF52-DK to learn as...
Hi team,
My customer wants to develop a system with one central, multiple peripherals, each bandwidth is <50kbps, but they want the latency can be as small as possible....
Hello,
I would like to know how can i use SPI on the radio example.
I'm using (programming) the radio example, receiver, for AoA and it's working so far. What i'm trying...
