Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
Hello,
I read through the datasheet of the nRF85832 to understand the peripherals a little bit better, but I got stuck while looking through the register overview (in this...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
Hi all,
I'm working on a project which I started from the multiperipheral example. I am using SDK 15.3.0 for this. I am developing the software on the nrf52840 DK using...
Start SEGGER Embedded Studio by clicking Open IDE //Successfully installed, what means Open IDE ? ? ?
Select File → Open nRF Connect SDK Project… //it just dont appear in...
Hi,
Currently, I am in a feasibility analysis stage for an application which requires BLE Mesh with Localization (RTLS using AoA and AoD). I explored SDKs for nRF52833...
Hello,
on SDK16, with nrd52dk, with android phone, standard ble_app_uart example works fine with nRF Toolbox. But when I disconnect from nrf52dk, the chip still thinks the...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I changed the device name while not connected.
but, The...
Hello,
I am trying to follow the tutorial SDK UART coexistence example , but it seems like the last step cannot be completed. As you can see, that .hex file does not exist...
I am working on a low power peripheral project (similar to the Nordic blePeripheral/uart example). I'm going to be using an nRF52805 with SDK 17 and s112. I found the Apple...
Dear all,
I have tried my best to find answers in questions posted previously but I still have a few questions that I would like to clear up. I will keep it concise. Thank...
I want to configure the UART1 (not the UART0), and I want to know if there have some examples that introducing the UART configuration by directing accessing the register....
Does Nordic have programming for the nRF52840 that enables both 802.15.4 and BLE, so the board can both become part of an 802.15.4 network and pair with a mobile device like...
