I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
Hi,
there are several devices with same Firmware/Modem firmware/Hardware. All device were working. While all others continue to work, one suddenly gives me this:
Once...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi Team,
We want to load azure certificate into nRF9160, can you please provide sample code, code snippet to load azure certificate.
Regards,
Sravan Rikka
Summary
On NCS v3.3.0 , building any application that enables the new Zephyr OpenThread Border Router L2 glue ( CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y , together with...
Hi! This is a general info post since i have found a temporary fix to it, but whilst trying out ntn, we noticed that when switching from %XSYSTEMMODE: 0,0,1,0,0 to %XSYSTEMMODE...
I'm planning to deploy a Thread network with 200-400 units and seeking best practices and real-world experience from the community. While the Thread spec allows up to 32 routers...
Hi,
we are developing on nRF54L15 using NCS v3.2.3 , and evaluating a DFU architecture based on:
MCUboot
firmware_loader
main application
using the BLE MCU Manager...
Hello
I'm currently working SDK upgrade from ncs v2.6.4 to v3.2.1
I found that, in fade in/out scenario, the PWM works well. however, if it need to turn on in 100%duty...
Hi Nordic Team, I am the beginner on this platform. I am trying to hear the PDM mic data in headset on nRF5340 Audio DK. Is it possible to do?
Please guide me as soon as...
