I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
We are trying to include the UART.h into examples\ble_peripheral\ble_app_hrs and are facing the said error even after including the file.
Can you please help with...
I try to how if boot/reset while power up the board and the LED5 is blinking but when I unpluged the cable and plug it again. The LED doesn't turn on any more. And the computer...
I am using nrf_serial in IRQ mode to communicate with an AT based device. When I reset the device using ATZ, I get NRF_SERIAL_EVENT_DRV_ERR -- likely because the pins go into...
Dear All ,
I am finally able to get my beacon app to compile and work on the nrf51822 using keil with s130 softdevice.
I tried to add service data to the advertising...
Hi,
I have a situation where I have to create 4 TWIS instances on nRF52832.
sdk_config.h only shows 2 TWIS instances.
Is it ok if I add other instances (TWIS2_ENABLED...
Hello,
I was testing output on a GPIO pin with the mesh/dimming_server example and was only able to see 1.6V when measured.
I read through the example on infocenter...
Dear All,
I thought i wrote this question but seems it did not get registered. We are using the Beacon App from sdk 12.3 with the nrf51822 chip on custom board. I have...
Hello, I'm still a beginner with mesh so excuse me, if this might be a silly question or has been answered before. I did not find a post that quite resembled my problem. ...
I'm trying to use some code from the sample files and given libraries to create my own custom program. Upon startup, this is what I get:
Here is the only function called...
I am Currently under process of evaluating various modules for implementing BLE Mesh, Had few concerns regarding the same, would be great if someone can clarify upon them...
Hello,
I have seen today that the new releases of the v1.0.0 SDK and v1.0.0 modem firmware were release for the nRF9160 DK. I have been able to update the modem firmware...
Hi,
I am trying to migrate my project developed on Mesh SDK V2.0.1 to V3.1.0. I followed all the steps you recommend but i am stuck with the configuration of my server node...
hi all ,
i run Serialization application between nRF52840-DK ,it not start up.
how to Debugging this issue? i have been reset connectivity board,the error message halt...
I am trying to connect the MS5611 ( https://www.te.com/usa-en/product-CAT-BLPS0036.html ) using the GY-63 Sensor Module to the n RF52840 with the nRF5_SDK_15.3.0_59ac345 SDK...
