Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I guys, I m trying to use the nrf52840 protocol in order to send an interrupts between two boards.
Looking at the examples provided in the SDK i didn't understand how to...
Hi, I have a particular issue that happens intermittently, I was hoping someone here has come across the same issue and possibly knows how to fix it.
My Setup:
Using...
Hi
I am trying to add manuf data to ble_app_hts sample advertisement but without success:
static void advertising_init(void) { ret_code_t err_code; ble_advertising_init_t...
nrf52840 last version of SDK Hello I need help. I want to start ble_adv and then stop with a button signal and start again with another button signal. The idea is
Loop:...
Hi,
I am using ble_app_uart example and want to detect the read evant/ call back. Kindly help me how to register a call back function of a read type characteristic. I want...
Hi all, I'm working on nrf52832 in segger embedded studio. Using ble scanner app, I'm entering some random values. So when i enter a value, I'm adding them to watch and checking...
Hi,
i am working under the mesh concept in nRF52. I saw the mesh demo in nRF thingy the link is here.
and i also have 4 nRF Thingy boards in my hand. i want to do the...
Hi.
I am currently weighing up whether to use a PCB or a chip antenna. Due to my product is going to be less than 20mm x 20mm, I would prefer the chip antenna to save some...
Based on mesh sdk 3.1, open NRF_LOG_ENABLED in the light_switch_server example, ie NRF_LOG_ENABLED 1, the following error occurred during compilation: Linking light_switch_server_nrf52840_xxAA_s140_6...
Hi
I changed the clock source from NRF_LF_SRC_XTAL to NRF_LF_SRC_RC, but it dit not work.
In the migration guide( Migration Guide ) I found out, that the method SOFTDEVICE_HANDLER_INIT...
Hello,
I am working on a custom PCB with NRF9160.
I have modified nrf9160 uart sample to add UART_1 and enable SPI_3 and everything is working fine.
Now I need to include...
Hi ,
I am using SDK v0.4.0.
Modem firmware : mfwnb1nrf9160030123prealpha
Asset tracker example is downloaded to the NRF9160-DK.
Since I am using NB IOT, I select...
I use nrf52832 sdk 14.0
SD+ boot(for ota）+app
In the applicaiton there are some user data to save. I used two pages ( one pages start from 0x6E000 and the other start...
