Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hi,
I use nRF5 SDK v15.0.0. In my application I need to change Bluetooth identity address. I can not use BLE_GAP_ADDR_TYPE_RANDOM_STATIC address type, because I need to...
Hi,
I have migrated my projekt from SDK 14.2 to 15.2, the bootloader is basically the secure_bootloader example with some tiny adjustments. When I try to upgrade my product...
Hi all,
I encountered problems porting MbedOS based software which uses Bluetooth Low Energy from MbedOS 5.10 to 5.11 to use the extended features od BLE 5.0.
The ble...
I have interfaced two Nordic nRF52840 boards with one as master an other as slave .
In the image attached signals from down depicts Salve seelct,SCLk MOSI and MISO of Master...
I run into problem, I think for now resolved, but questions remain: Do I have to stop BLE whenever changing ADC config? What did not work?
I don't know why it does not...
Hi, we made a custom board with nrf52832 and flashed example code experimental_ble_app_blinky from sdk13.
We are trying to change the radio txpower other than 0db (default...
Hi all,
I have a nRF52840 development kit and flashed (I believed it flashed successfully) with direct test mode .hex file from SDK 15.2. What I facing was not able to run...
NRF52840 - SDK 15.0 + Some register based custom functions. S140, 6.0.0. In order to work around some of the hardware limitations with SPIM in the context of a project, we...
The PWM Driver has all sorts of fancy stuff for dealing with clever sequences - but I can't see anything to just set a simple, steady, fixed duty cycle!
How does one just...
I need to configure 2 devices as relay nodes in order to relay messages from the client node to the server node
How can i implement this in the light switch example ?
I know this has been asked a few years back, but wasnt sure if there were any changes to this. I want to be able to detect when a connected device is removed from windows...
Hi,
I use nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10040_ble bootloader. I upload my app to my board using PCA10031 and nRF Connect v2.6.2 on Win10 and...
Hello,
Our board is based on nRF52832 with S132 5.1.0, without RTOS. Now we have a requirement to protect sensitive memory areas with MPU, so I'm trying to run firmware...
Hi,
I am using nrf 52840 development board for developing mesh. I am using segger IDE in my windows 7 desktop for code flash to the board.
The SDK I am using is nRF5_SDK_15...
Hello to everyone.
I have a doubt about the function of NRF_LOG library in nRF52 DK. I´m trying to display the voltaje value from pin P0.26 on Termite, so I saw in this...
