In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello everyone, I've followed the following guide for mesh dfu and had no issues with the example provided here : https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK...
Hello,
is it possible to set the sniffer/firmware to follow the central device instead of the peripheral?
Currently, only peripheral devices are shown in the device...
I'm attempting to get a grasp on how much CPU time an SAADC conversion is taking. I'm running the SAADC sample code from the nRF52 v15.1.0 SDK on an nRF52832. SAADC_CONFIG_RESOLUTION...
Hello everyone, We want to program the other NRF52832 chip from the NRF52832 chip via OTA. The DFU service UUID is 16 bits (0xfe59). However, the characteristic UUIDs are...
Hi,
I'm using the nrf5283 chip alongside with the SDK12.1. I have a strange situation related with the bootloader dfu.
First I flash with the programmer a merged hex...
Hello,
I'm working with Mesh SDK 3.1.0.
I made some changes in app_level.c file.
Could you please confirm that these changes are right?
They seem to work fine, but...
I am using SDK 15.2
I downloaded both nRF Toolbox and nRF Connect applications on my phone (Lenovo K6 which is running Android 7.0 but i tested the same thing on multiple...
Hi,
I'm attempting to flash program a Nina B112 Bluetooth Module (from Ublox), which is built uppon a NRF52832 board and i'm attaching this module to a custom board.
I...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
