Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hey there, I have a problem when use the command nrfjprog --memrd xxxx.
I was running a simple blinky led example on a nrf52 custom board, then i read some information from...
Hi all,
I am working on a project which receives data from UART (15 bytes at every 40ms interval). I want to store 1 minute of data on the NRF52832 RAM before sending it...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
Hi,
IC : nrf52832
SDK : Mesh_v1.0.0
I am testing the light_switch demo of the Mesh_v1.0.0.
I don't have 32kHz osc on my server board, so I have to change the clk...
Connect USB to PC, no "JLINK" device. But connect USB to PC and press reset button at same. I can see "BOOTLOADER" device.
How can I get my board to normal?
I am trying to create a network mesh using the multiperipheral example.
In the original version the communication is possible only:
central >> peripherals
peripferals...
Hello,
I am wondering if you have any plans for implementing a Softdevice that supports BLE mesh network on nRF52832 in near future?
If not, if I were to implement it...
I'm reading about beacon scan response requests and scan response packets, where a client (like a phone) can request the beacon respond back with local name and other info...
Hello,
I need to implement mesh networking capability in the beacons which are ble5. Can anyone explain me how do we achieve that?
I want send specific data via one...
Hello,
I have nrf52832 and sdk14.1.
Everything works fine but after starting the device i get this information and there is no further progress from there on:
<info>...
Hi,
I need to make two FSRS to read and display the output simultaneously. So, initially I had to get the ADC values from two analog pins at the same time. After struggling...
