I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Still trying to get anything ta all to work on the nRF52-DK
I erased the chip
I flashed the soft device "soft_device_s132_v3.3.3" to address 0 and verified
built...
Hi!
We are having problems with pairing & bonding procedures with iOS devices.
On the peripheral side we are using a nrf51822 BLE module on which we are testing pairing...
Hi all,
2 days before we bought nrf52832 board.
in new board i can able to execute all peripheral example ( LED BLINK,button,uart,timer..)which doesnt need softdevice...
I'm trying to setup the RTC in the nRF52 to count with a resolution of 1mS. As the count has only a 24 bit value, I wish to clear the count every hour to start again.
There...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
I measured my Nrf51822 current:
when my VCC is 3.0v ~ 3.3v
my current is 0.16 mA.
when my VCC is 2.6v ~ 2.8v
my current is 1.5 mA (why?)
when my VCC is lower than 2...
I have issue with nrf51 booting, i noticed that sometimes when i plug the power to (VDD and GND) the system dosent turn on at al.
1 - how does the system the whole system...
amigos de habla hispana estoy comenzando con este circuito.
mi duda es cual compilador utilizo para crear un simple led blink..
tienen algun tutorial en que me puedan a...
Hi.
I am using the nRF52 Preview Dev. Kit to send data over multiple channels by
setting the NRF_RADIO->FREQUENCY register to the desired frequency value.
To make it work...
Hi,
I am trying to measure the temperature using sht21 sensor with nrf51822. I am using TWI to do this. When I try to send a data to the sensor the application cannot do...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
