Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
HI all,
We've recently moved to SDK 11.0 and it certainly has not been a painless migration, especially when using GCC.
Setup: GCC 5.2.1 on Linux Mint with nrf51 xxAA...
Hi, I'm wonder it is possible to stream video using nRF52x family? I know that chipset isn't designed to this purpose, but I'm only wonder about that.
Thanks
Robert
Hi,
I've started using the nRF5 11.0.0 (89a8197) SDK on a board that does not include an external low-frequency CLK source.
When using the nRF52 0.9.2 SDK, we were recommended...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
Hi, I am working on eddystone project i.e nrf5-sdk-for-eddystone-master which is newly released by nordic. And I set URL,UUID and TLM frames successfully but when I trying...
Hello,
I am encountering a very strange problem with the Timeslot API.
I am developing with s130 and using the timeslot example provided by Nordic to
send data revived...
So far I've been prototyping everything on an Arduino Zero connected to a nRF24. Is switching to an nRF51822 an option for me? or will I have to switch my entire code to work...
I need to communicate with several nrf modules, 1 rx and at least 2 rx. I started with nrf24l01 but it has no rssi. For that reason i bought nrf51822.
What i have to do to...
hi,
i have doubt regarding NRF 51822BEACON KIT [pca20006 board],
......i want to configure it in all ble modes [central,periperal,broadcaster,listener],
how can i do...
