Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi,
In my application I want to communicate nRF24L01+ with nRF51822 with dynamic length. Some settings are:
In nRF24L01+ side (reference: devzone.nordicsemi.com/.../)...
Hi,
Now I use these fun in ANT SD210 like below:
void MyFlashWrite(ble_ant_csc_t* cscdata)
{
uint32_t addr;
uint32_t patwr[3];
uint32_t pg_size;
uint32_t pg_num;...
what information does the nrfjprog.exe write to UICR(User Information Configuration Registers) register??
==========Tutorial of Flashing dfu bootloader to the nRF51 DK...
I want to use the ble sniffer to capture two peripherals connected to the master control panel.
with the ble sniffer I can only select one peripheral for capturing packets...
Hey there, I've posted this issue on the tutorial website and I came across a post stating that posting here will get me a quicker response. Here's my problem, when I tried...
In my application need to nrf8001 connect(bond) to e phone in a specific duration (for example 1 hours )and then disconnect and in one hour later bond again. In this duration...
Hi,
I am developing a Heart Rate application.
I need to ensure that i am flashing correct softdevice file through my application.
How can i do that?
Regards,
Sum...
Hi,all
i study DFU step by step according this link devzone.nordicsemi.com/.../a00076.html,but failed at step 8.my peripheral advertising as Nordic_HRM not dfuTag.
Can someone...
hi,
I used previously nrfjprog version 5 to program SD+APP+BL with --dfu flag and I can perform OTA DFU.
Now with version 7 there is no --dfu flag anymore and if I try...
Same question as devzone.nordicsemi.com/.../
What needs to change for a gcc setup in the compile flags.
If that helps, some of the flags I have now include:
-mfloat...
Hi,
I'm using s130 and my mcu is both central/peripheral. In the centrol role, when I try to connect and pair with an peripheral, I get all the way through SMP pairing...
I have been developing an application using PCA10028 board which needs to use timer. From the SDK8.0.0 pack, I found an example "timer_pca10028". It works fine when the SD...
Hi,
I'm trying to get a simple single packet transmit-receive working with the nRF51822. I have the following code shared between my transmitter and receiver:
#include...
Hello,
I am wondering how the Softdevice works internally with state changes because that's important for error handling. Here's an example:
Let's say the Softdevice...
