Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I am currently working w/ a project that utilizes TrustedZone and PSA Protected Storage to read/write to internal flash that's accessible only in the secure partition (I'm...
I am in the process of migrating to NCS 2.7. My project includes NSIB, MCUBoot, TFM, and the application. Everything works fine with multi-image builds.
However when using...
Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint?
I would place copper keepouts under the reserved pin areas to ensure...
Hi,
I cannot start HFXO on nRF52832. I'm using 32MHz crystal TSX-3225 32.0000MF20X-W0(from Mouser) wtih 12pF caps UMK105CG120JV-F(also from Mouser).
Checked with beeper...
Working on a wearable health sensor using NRF5340. Hard to be certain of correlation, but glitches of varying magnitudes appear on my sensitive analog signals (as captured...
Hello Nordic Support Team,
I'm encountering a persistent issue when I try to flash an nRF52832 board using an nRF52840DK (PCA10056, nRF52840_xxAA_REV3) with nRF Programmer...
Hello Nordic friends,
I am currently testing the device, but I absolutely don't want to use Zephyr or any advertised MCUs. I wrote a simple code for scanning and testing...
I have a custom nRF52833 wired to an Adafruit USB Micro-B Breakout Board, and when I plug it into a Windows computer, it gives a device not recognized message and no COM port...
Hi,
Our custom hardware makes use of an external flash device, IS25LP032D-JTLE-TR, for storing files (littlefs) and OTA updates. We've noticed, seemingly only after a power...
I get an error and the flashing fails when I attempt to flash the nRF52840 DK via an external J-Link Plus connected to the Debug In connector (P18).
Programming of the nRF52840...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
Dear Nordic
I use nRF5 SDK BLE_Central / uart to connect our custom peripherals by address, and I found that it seem need to 4~5 seconds to finish connecting
Here is the...
Hi there.
I am currently working on WIFI provisioning using BLE using nRF7002 and nRF5340.
The CPU structure of my custom board is based on the nRF7002DK. So I am testing...