I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
hello.
Currently I am implementing BLE Multi advertising in
NCS SDK: version 2.6.0.
I have a question during development through the samples/bluetooth/multiple_adv_sets...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...
Hello,
I am writing to seek clarification on the difference between AT%XRAI and AT%RAI. I was testing the RAI feature using the SLM application (SDK v2.7.0 and modem firmware...
trying to program an nRF51422 chip with Segger embedded studio with soft device
i get the error
"Checking project status Building ‘ble_app_uart_c_pca10028_s130’ from solution...
Hello,
I have a custom board running as a low power node, consuming around 17uA during sleep. When I have messages back and forth, the node goes back to sleep as usual....
Dear support team: Problem description: Use \v2.7.0\nrf\samples\bluetooth\mesh\light routines to download to nRF52840-DK board, after adding it with nRF Mesh app (Android...
Hello,
I have trouble again with TX Power control. This time using Softdevice Controller and NCS2.6.0.
Previous issue which was solved (this was using Zephyr Controller...
I'm working on a Proteus-III module which needs to communicate with the on board UART0. For reasons that I still don't understand, the `uart_configure` function with which...
I would like to test event related functions on nRF5340 DK. But west build failed with undefined reference to `z_impl_k_event_init'. The following are log messages of west...
Hi,
I am trying to connect 4 devices (2 nrf devices + 2 B24 custom modules). Each of them can get connected independently as single device, but as soon as I start connecting...
I'm reading the code of peripheral_hids_mouse project and I want to select some functions to fill my own code.
prj.conf has these two config:
CONFIG_BT_GATT_UUID16_POOL_SIZE...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi all!
I've been working on a project using the nRF Connect extension for VS Code and I've been trying to figure out which HEX file in my build/zephyr folder for my application...
Hi,
I am sending a SCAN_REQ packet from my code after receiving an Advertising packet from the NRF5340 DUT. Sometimes I receive the SCAN_RSP packet, but other times I encounter...
