Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
I am trying to build an application that can switch into MCUBoot's serial recovery mode and receive a new firmware image over the serial port. I'm using NCS 1.7.1 through...
I'm using the nrf9160dk (ns). I started an application based on the SIMPLE_MQTT sample. At first, every this worked. I added my one MQTT client with a different set of buffers...
Hi,
The LE Secure Connections Multirole Example is automatically requesting a pairing/bonding.
Why is it not first just doing a connection and requesting the numeric comparison...
I cannot locate an app in nrf connect for the desktop. What can have contributed to this? Can it have a relationship to the network?
Thank you for your help.
I'm doing some experiments with the nRF52840 and SEGGER Embedded Studio. I'm quite new to C but managed to get desired results using and changing the examples. I'm now trying...
Unable to configure hCI Uart project in Segger Embedded
I need to configure the HCI_UART project to support DTM testing, but I cannot enable the configuration parameters...
Hi
We are a group of students working with the nRF9160dk.
We want to try connecting the nRF9160dk to google cloud and send data through MQTT.
We have tried to follow...
Hi,
We want to build PCB using nRF52840. Previously we were using this package but it is out of stock. I want to ask can we use this instead of the previous package. Are...
