Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I first assumed the obvious that the first library would be used with the (Visual studio) multi-threaded DLL/MD option and the second would be used with the multi-threaded...
Hi,
Currently we're developing RGB bulb which has mesh feature (nRF52832). So this done by using nRF5 SDK 15.2.0 and Mesh SDK 3.0.
We're able to control all three channels...
Hi Team
I would like to store a simple integer value in flash and read it back after a power cycle. I already studied the library Flash-manager of the nRF5 SDK for Mesh...
Hello, I'm trying to flash custom developed beacon based on nRF52811 and everytime i try to flash i'm always greeted with an error "Failed to write memory" i have attached...
Hello,
I am trying to merge mqtt_simple and gps together. Each of them is working well on Thingy:91.
1. I am using lte_lc to configure the modem and enable PSM and eDRX...
Hello All,
Right now I am working with: https://www.digikey.ca/en/products/detail/circuit-dojo/PASSY-NRF9160-FEATHER/13668137 which I think is practically the same as https...
As everyone knows, the supply of semiconductors is pretty bad now. Normal suppliers such as Digikiey have zero stock. Recently we have had to purchase from less known distributors...
Hi everybody! My application is based on SDK 17.02. I try to communicate with an spi device using spim driver and the code is basically based on the nrfx-spim example.
After...
I am using latest version, nrf connect sdk v1.4.99-dev1
when activating bt_enable, application gets stuck
applications without BLE works well
I am working with...
Hi I'm Frank.
I'm testing Serial DFU via UART using TWO nRF52840 DKs(DFU master and DFU slave DK).
I want to update firmware of slave DK through the master DK.
I was...
dear all:
I use the latest sdk17 to test the ANCs sample on the 52840 DK。 The address of the example is: SDK_Path\examples\ble_peripheral\ble_app_ancs_c。after...
I have a example application (gatt central) that works fine on the nRF52DK dev board. I'm able to change the advertisement name, connect to it with my phone, and see the characteristic...
Hello everyone,
Yesterday I found a strange behavior with the NRF9160 GPS on NCS v1.5.1:
When configuring the GPS to run in Single Fix mode, running on MFW v1.2.3, I noticed...
*** edit: Problem solved. My project file had build config set to "release", I had to change it over to "Debug".
Kindly close the case ***
I have an i2c program running...
Hello,
I would like to ask for guidance, as I am at the very start of a human interface device (HID) controller development, considering BLE nRF52840.
The use case I would...
