Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Dongle cannot enter reset mode, and led is not pulsing(no shine ) when I connect to PC, the device cannot detect it,too. Is their any problem on the firmware, the device cannot...
Hello there,
I am trying to find the datasheet from the device NRF31502 F but I am having some trouble!
Can someone help me or point me where I can get it?
Thanks
Dear all. Now I am working on multi-peripherals to one central NUS communication project. The peripheral boards are based on nRF52840 and the central board is nRF52832 DK...
Hi Team,
We want to write our own MAC address on nRF52840 module. It's a production level MAC address i.e. it is fixed MAC address cannot be overwritten. What is the procedure...
Hello,
I am using SDK 14 & nRF52832 & peripheral role; I have setup a timeout in the order of several seconds, and during this time my device shall advertise but reject...
Hi,
I'm using nrf52840 and trying to define the pin mappings for my custom board. In order to do this I'm studying the board definition of pca10056 (pca10056.h).
In...
Hey all, I'm trying to run the node cli flash "imei" -f /path/to/firmware.hex command on the terminal. It prompts as ERROR flash <deviceId> failed!,
ERROR Error: No such...
Hi
I'm working with version v8.6.90 since the master version at this date have an Auth amplify issue.
The Fetch function on the map is buggy :
Here is the Chrome dev...
We are using nRF52 SDK 17.0.2 s132_nrf52_7.2.0_softdevice.hex in our application. When entering in DFU mode from application, we perform nrf_power_gpregret_set(BOOTLOADER_DFU_START...
I am willing to use nRF52832 chip in one of my project. But all the breakouts dont fit the size and I want to design my own PCB with i2C accelerometer. I only want to transmit...
Hi,
Corect me if I'm wrong, but the initiation of ble_gap_addr_t.addr_type in main.c in the HRS_C demo is not necessary, as the addr_type is calculated based on the address...
Hello Folks,
I am following below steps to add Zigbee FOTA to Zigbee: Light switch example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_zigbee_configuring_libraries...
Another problem is that when I turn on I2S to read data, the while loop does nothing, and the broadcast can't be transmitted, just like I2S has occupied all the CPU, and other...
Hi Devzone,
I use original mqtt_simple example to test connecting with MQTT Broker.
I ran it on Ubuntu, SDK v1.5.99. When I press button to publish message, some errors...
I'm planning to evaluate AoA and AoD using nRF5340 DK. I asked my local RSM about getting the antenna array and was advised to get nRF9160 DK.
After reading the documentation...
