Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
I have done a number of BLE projects using this chip. I am exploring two potential applications which would use the 2.4 GHz radio, transmit only, in a non-standard way. I...
Hello.
I've been asked to help develop an IoT device where GPS positioning and transmitting status via LTE-M/NB-IoT is central. So I've landed on the nRF9160 device, which...
I have a project bord which base on nrf9160, two buttons are set in the hardware circuit, corresponding to the pins of P26 and p15 respectively, and P07 is used as the interrupt...
It appears on the Thing91 reference board that the SIM_DET pin is used to drive the SIM mux control pin. Is that case? Is there more information on how to use this?
Is it acceptable to use the nrf52805's DEC4 pin as 1.3 V reference? I've connected the pin across a ~11 MOhm divider to to create a 0.12V reference for an op amp. I figured...
On SDK16.0.0 + Mesh SDK 4.1.0
I am using a Fanstel BT840X module that has an onboard Skyworks SKY66112 PA/LNA.
I followed the Infocenter guide along with an old example...
Hi, I'm having an apparent memory issue after increasing my PPI channel and GPIOTE allocation. Here's the basic setup:
nRF52840 with SoftDevice 6.1.0
SDK 15.3
I...
Hello,
We're intending to use the free flash region for two purposes: Flash Data Storage and DFU. The Flash Data Storage will be allocated a large number of pages (100...
I am using the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant parts to my app.
It is now apparently working. The...
Hello ,
currently i am working on indoor navigation project for that i was setup 4 node in a square shape, the nrf52832 beacon was continue transmitted packets. we also...
Hello,
I've been looking into the performance of the coded PHY (S8) to see if it fits the needs for a product we intend to make. All research and documentation I found about...
Hi,
Im currently wondering how I would power the nRF52 dongle with a 3.85 Liion battery the best way. Voltage range will be between 2.5v and 4.2v.
I read you can use VDDH...
Hi, I am trying to make the iBeacon emulator using nRF52840-DK without SDK. I have found the iBeacon packet format.
When I send this packet using SDK, that worked. Now...
Hi all,
I am having a problem with the startup of the software on an nRF52840. It works fine on an EVM but not on our own board. The software is hanging in the softdevice...
