Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
I can successfully download an image using nrfutil dfu serial when I use a test image (compiling the bootloader with the Nordic default public key) and the application starts...
Hi,
My requirement is to validate the PCA10040 dev board with a different set of UART pins. I have tried the following steps, but as soon as I start the firmware, it crashes...
Hello, I am new to BLE development and RF design. I've been doing as much reading as I can about RF design rules for PCB's, antenna performance, etc. Yet I am still uncertain...
I am trying to get a BMX160 working over SPI. I was following this post to make this code using the SPI example from the SDK as a basis. I am using SDK 15.3 with a nRF52840...
The app is foreground -> I am very easily connected with BLE device.
The app is in the background -> I get the callback and connect with the BLE device
The app is removed...
Hello.
I'm trying to get the example bootloader Segger project (secure_bootloader_ble_s132_pca10040) running on a custom board I have that uses the nRF52832 as its core...
I am working on nRF9160 and i found that when i change prj.conf, i need to rebuild code. if rebuild is not done(only build is done), changes made in prj.conf does not comes...
Hi
I'm currently evaluating the possibility of using nRF5340 in an upcoming project. As the chip is very new it's easy to understand that all specifications are not yet...
Hello, I am using nRF SDK for Mesh 3.1 and nRF52940 SoC. I have two nodes in my network which both act as a client and a server. Both of them subscribes and publishes to same...
Hi,
I am working with ANT bpwr tx profile and trying to implement HX711 and TWI sensor to it. TWI sensor is already working, but when I add library for HX711 from and start...
Hello,
It would be nice if the HVN tx complete event structure had the attribute handle of the characteristic that was just notified. This is already done for writes and...
Hey guys,
I'm working with the Laird DVK-BL652 and the Nordic SDK v.14.2.0 with Eclipse (Kepler) and try the example "SPI Master". I didn't modify this example but after...
Test Setup:
SD 6.1.0
SDK 15.2.0
Peripheral: nRF52840
Central: iOS 13.1
Central is connected to two peripherals, each peripheral is sending 50 pkt/s, each packet...
Hi,
We have a nrf51822 based custom board with no button, we use accelerometer tap detection to wake up the system. Currently there is no software protection for the battery...
After getting my nRF9160DK activated and showing up in the NRFCloud it would just sit there blinking led3.
I deleted the device from the cloud and tried to update modem...
