Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
We bought a handful of nRF52840 Dongles and want to develop firmware based on the nRF Connect BLE app + nRF connectivity firmware reference design.
I am using v2.6.2 of...
Hi,
I need to read RSSI value without implementing the SoftDevice. Now I'm producing modulated and unmodulated carrier starting from the radio_test example. How can I read...
nrf52840 is ble central ,nrf52832 is ble peripheral,
nrf52832 is modify finish.
but i do not know how assign ble central .
now i use the example(ble_app_uart_c) to implete...
Hi,
I am using Timer0 to measure external pulse width. Using GPIOTE, PPI task and events. The problem here is, I am reading Timer0 Capture register as Zero always. Here...
Hi,
Now I'm using window10,nrf52840 and nrfSDKforMESHV3.1.0, and I want to achieve ota fonction within two nrf52840,I had read the Software Development Kit > Previous versions...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
How to select different Advertisement types ADV_IND/ ADV_DIRECT_IND/ ADV_SCAN_IND...
I have my nRF91 DK connected to nRFCloud, thanks for making that super easy! I'd like to review any debug data and learn more about the nRF91 which is new to mean but when...
Hello there,
We are a test lab based in Leatherhead UK, and would like to use your nRF52840-DK for setting up a test jig to communicate with a DUT(Device Under Test) ...
Hello,
I am trying to determine whether or not the SPI EasyDMA functionality of the nrf52840 supports double buffering in the sense that the DMA controller will switch buffers...
Hello, I have a problem with properly adding the Azure IoT SDK (C) into Segger IDE. Anyone already managed to get through that? My goal is to have Azure IoT Hub working with...
Hi, I'm attempting to use the nRF52832 Smart Remote 3 SDK for a project on an nRF52832. I wish to add Serial Output capability (for debugging purposes). I followed the example...
Hi,
I notice that inside the MESH SDK, "Friend" is actual a hex file from zephyr, which I cannot modify. My goal is to set a "Friend" to connect more than 1 LPN (low power...
Hello, community. I have a question about hardware and software setting for using 32Mhz.
(1) Software setting in sdk_config.h
#ifndef CLOCK_ENABLED #define CLOCK_ENABLED...
Hi, I'm searching a example project to do the qualifications test for my product. I'm using SDK 10, have you an example for this SDK? (in your site I found an example with...
Hello
I'm trying to maximize the throughput between a NRF52832 and iOS devices in both directions.
Currently, I seem to achieve about 400 Kbps from an iPhone 8 to the...
