Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
i am working on mesh application in nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for SDK...
Hello,
I am using custom board with nRF52832 and Keil uVision5 as IDE. I started with simple example which is just to ON the LEDs.
Code(all necessary header files are...
Hi,
I'm developing a FW that is now validated. We are "almost ready" to go in mass production (6000 PCE for the first batch).
For the moment, I'm still using the debugger...
Hello,
I am using the mesh pb_remote example in order to have a multihop scenario. I would like to do some latency calculations, so some kind of bidirectional communication...
Dear all,
I'm using NRF52832 with SDK 14.2.0 and SD 132 v5.0.0.
I have my own implemented application working properly when is flashed directly without bootloader, only...
Hi,
I'm wondering if anybody has performed a test of, or has experience with Nordic Semiconductor thread mesh stack (nRF5 SDK for Thread and Zigbee v1.0.0) in a large scale...
Hi, i used the 'nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch' i have two question:
1: How to added more Client in one mesh net?
2: How to configuare node to 'low...
I am trying to make RF USB dongle using nrf52840.
Before the PCB production, we are using DK to test, but the firmware is not uploaded because VDDH and VBUS of DK are connected...
Hello Nordic!
Sometimes we have a problem with a services discovery. We have no custom services. Only DIS, BAS, NUS and DFU. (nRF52832 and SDK15)
This problem is currently...
Hi,
I'm working with the light_switch example on Mesh 2.0.1 and I would like to modify the simple_on_off_client_set_unreliable function to broadcast to all servers in the...
I am evaluating TAIYO YUDEN board EKSHSNZWZ.
I've flashed s132_nrf52_5.0.0_softdevice.hex using nRFgo Studio.
I use Keil uVision to test "nRF5_SDK_15.0.0_a53641a\examples...
Hi. I am trying to transmit a microphone signal to the nrf52832 DK board.
Before development, i checked it by connecting a microphone(ADC) and a speaker(PWM) to one...
It wasn't until I downloaded nRF-Sniffer-v2 that I discover the release note below that explicitly states that nrf_sniffer now supports all platforms supported by Wireshark...
Hi,
We want that any bulb or any devices (Server device) of BLE 4.2 should be able to work with BLE Mesh SDK(Client). We are using the nrf52832 with SDK BLE_2.0.1 for the...
