How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
HI,the current situation is that nrf52832 can not receive the ack_payload from the nrf24le.
nrf52832 as DEVICE,using the project NRF5_SDK_13.0.0\examples\multiprotocol\experimental_ble_app_gzll...
I am a beginner and I need to know how we can further modify the light switch example codes to access gpio pins and get some output from that.
I have run the example using...
Hi to all team members.
I am using nrf51822 working at 16 MHZ clock.
I have interface 3 sensors ECG, SPO2 and GSR sensor analog output to nrf51822 on 3 respective channels...
Hi
I have N number of beacons and one observer having nrf52832. I want to have the number of unique beacons available in the scanning range.
Do the s132 soft device provide...
Hi everybody,
I suppose our question is mainly in the title.
ThingyLib version is 1.0.2
https://github.com/NordicSemiconductor/Android-Nordic-Thingy/tree/master/thingylib...
I am trying to send the MPU6050 data using BLE nRF51822. I have used ble_app_uart example modified it to read the data over I2C and send the data over BLE. I can successfuly...
