In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Most examples, tutorials, and standard BLE service implementations within the SDK (14.1.0) seem to use the BLE SoftDevice's sd_ble_gatts_characteristic_add() when adding a...
Hi,
I know that this question has been asked before but it seems like the answers are pretty old.
I have a need to scan on one channel only to receive advertisements...
Hi,
As mentioned in this post:
devzone.nordicsemi.com/.../
the struct ble_gap_adv_params_t --> ble_gap_adv_ch_mask_t give the option to turn any advertising channel...
I'm calling sd_ble_uuid_decode with the following parameters on a PCA10040 board:
sd_ble_uuid_decode(16, 0x2000F7CC, 0x2000F7DC)
ram base = 0x20003150
vs_uuid_count...
I want to use in my project tft 1.8 display with st7735 controller. I used the standard GFX example from SDK 14.1 and everything is working fine, but the picture is incorrectly...
I have a QFN48 nRF52832, and it's getting hot. I'm looking at it with a thermal camera and there's a hot spot directly under the "N" of the "N52832" that's on the package...
The BLE_NUS_C_EVT_DISCONNECTED of the ble_nus_c_evt_handler() give a conn_handle = BLE_CONN_HANDLE_INVALID . So it's not possible to know which peripheral got disconnected...
Hi everyone !!
I'm a beginner in ble mesh. I'm working with nRF 52840. I'm not being able to figure out how to see log messages. I want to know where will following line...
Is there anywhere I can find some high level documentation on the FDS module? I'm going thru the API documentation but it provides very little insight into how to best setup...
Hi Nordic Devzone,
First i want to make sure that if the clock being used by softdevice is the LFCLK (32kHz) and its counter register is 24bits ? and which prescaler is...
Hi Guys!
I am a newbee to develop a BLE IoT, and I am really trapped:
first of all: I am using the UART example from the SDK (12.2)
I'd like to send a float array with...
Has anyone been able to successfully connect a BLE device to nRF Cloud using an Android device as a gateway?
I don't see many posts or discussions around this topic. After...
Hi,
I am developing an application, in which I need to store the data collected from various sensors in external flash, in a particular format (Dataset no. - Sensor1 data...
When I use sniffers and wireshark for debugging (ble_app_uart), I found a strange place.
The following are the empty data PDUs seen from wireshark:
50ms:
Master-...