Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi I followed the Nordic UART example code to read and write characteristics to a Nordic S110 nRf51822 device.
My code is the same as in writeRxcharacteristic but when...
When I'm single stepping my nRF52 application in Keil with a BLE connection I always get the softdevice_fault_handler called.
I'm using SD 132, v2.0.0 and the the parameters...
What is the maximum clk frequency that can be output on a gpio for the nRF52832 ? I want the nRF52832 to output a clk signal on any of the gpios to an external module, and...
Can anyone please suggest a simple example on initializing SAADC Driver on one pin and do a simple blocking ADC read?
Sorry for a very broad question - but rather to ask...
I'm using the nRF52 Dev board and set the --rbp ALL option while using nrfjprog. It worked fine, and I am able to do OTA updates as I was testing the bootloader example. But...
Hi
I'm doing one project that is taking data from uart and send to mobile app. I'm facing one issue that is when I connected to peripheral it connected and take data from...
I'm looking for some options to extend the PCA10028 with a keybord and a numpad. This would give great options to play around with passkey topics.
As the PCA10028 supports...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hello,
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. The ANT Updater shows that the Image Upload is completed. I am uploading the...
Hi,
I there a way that I can detect if a sections of my code has been interrupted by the Softdevice? I have some time critical code (bit banging a communication protocol...
Hi All,
I am using the nrf51422 and softdevice S310 to send out ANT+ and BT Smart in my project.
I use RTC1->Counter in order to get a timestamp for an interrupt from...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hi,
I am trying to run an example project which includes a softdevice using Keil uVision on nrf51822xxAA. What should I change in Options for Target? Especially what should...
Hi,
If I connect a peripheral and establish a bonding with MITM the connection security changes to mode 1 / level 3. If the peripheral is disconnected and reconnected the...
Hi,
I am trying to write program follow this structure: first I will enable button using GPIO, then wait botton is pressed, then I read ADC from GPIO pin, if ADC value >...
