Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi，
For the SoftDevice controller， how can I send LL_MIN_USED_CHANNELS_IND messages？ Is there an API for this, or what scenarios trigger the sending of this message? Thanks...
Hello,
I'm measuring the power consumption on the Thingy:53 using the Debug and Current measurement board. Initially I was measuring the current of the battery VBAT given...
I have been using the VS Code extensions for setting up and building projects. Sometime yesterday build times went up from < 20 seconds to 10+ minutes. It looks like it's...
Hi,
I am starting a new development project on the nrf9160. It's a battery powered cell connected device using MQTT and Memfault.
Is it better to start a project from...
I need to measure the battery percentage using adc. i have created an application for ADC and its measuring correctly. Now i need to measure the battery percentage of another...
Hi,
I'm trying to measure message travel time using Gazel and k_uptime_get() so I can understand the packet intervals.
I'm using gzll_ack_payload_device and gzll_ack_payload_host...
Hello,
I am trying to control a PPK2 using my Raspberry Pi 3B+ running a 64-bit image of the Raspberry Pi OS (Debian Bookworm port) and I've been using python (v3.9) with...
Dear Nordic Team,
since the last release of NCS 2.7.0 the sd-card support breaks for me.
I am using the nrf5340 Audio DK with an inserted SD Card, and am running the zephyr...
Due to upgrading SDK2.5.0, I need to re-certify Thread1.3 in order to get a new CID for the previous module.Now I don't know exactly how to fill in the section of Thread Submission...
I have an application that requires invoking multiple commands to the same node in quick succession (multiple times a second).
To evaluate the feasibility of this, I flashed...
I am designing a pcb containing nrf52832. However, since I need a large number of GPIOs, I do not want to use the optional 32khz crystal in my circuit. But I also want to...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
Hello! I am an engineering student at KTH studying embedded electronics and I will be doing my thesis work for a company in about 6 months where I am supposed to be analyzing...
Hi everybody,
I'm just getting into Zigbee and try to follow the example at https://docs.nordicsemi.com/bundle/ncs-2.5.1/page/nrf/protocols/zigbee/adding_clusters.html to...
