Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
Hi,
I am facing a peculiar problem, wherein my application has two threads as in below:
Thread-1: is a preemptive thread which has UART functionality, along with UART...
I'm trying to run uart secured bootloader example in folder: @NRF5_SDK\examples\dfu\secure_bootloader\pca10040_uart_debug
but it doesn't work.
My setting is:
base...
Hi all!
I have created a simple application that only turns on a led and power it off using BLE in NRF52810. The thing is that simple app uses a huge RAM (~85%) and flash...
Hello,
I turned on the flash protect function through the CONFIG_FPROTECT switch, and the system kept running until spm_config_flash restarted.
Flash protect code in...
Dears,
Our custom board using nRF52833 cannot connect to Jlink after flashed a program.
I had the board connected with the Jlink via VCC, GND, SWDCLK, SWDIO and RESET...
Hi All,
I have a system with an nRF52840-dongle (PCA10059) acting as a serial port in windows 10. It runs extremely slowly. Sending 8kB over the interface takes 3 minutes...
I have the launch.json as shown below so that I can attach the debugger to a running image. This works with Cortex Debug. However, when using nRF Debug it does not seem to...
hi,
I'm using nrf connect sdk to communicate spi sensor.
which is better choice to use SPI in ncs (nrfx driver or zephyr ) ?
i) nrfx_driver: nrfx_spim_init(&spi, &spi_config...
