We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, I have a project that is comunication between nRF and Smartphone via BLE and using libuartes to comunicate with 2 another devices via 2Uarts. Now I need to combine 2 examples...
I have an BLE peripheral application running on a nrf52833 with softdevice S140 were I transmit data from Bluetooth to an external CAN-controller via SPIM and back. This is...
Hi, I want to enter the DFU by setting the register.But when the sd_power_gpregret_clr and sd_power_gpregret_set are set to set the register, and the err_code is 0x02 is returned...
HI
dk:PCA10090 0.8.5
modem: mfw_nrf9160_1.2.3.zip（ This DK board supports modems up to this version ）
ncs v1.9.0
example :serial_lte_modem
The NB card has been...
I added DCDC-enable to ble_app_beacon and measured the current consumption. As shown in the figure, spike current is generated during advertisement transmission. what is the...
Greetings,
I am running the "ble_app_template" example on my custom board using SDK v17.1.0. I am trying to figure out how to wake up the MCU from the SystemOFF sleep...
I currently am working on a BLE device in which I am trying to set the Service and Characteristic UUIDs. Here is an example of what I mean:
As can be seen here, the Service...
Hi there,
I'm in the midst of migrating between SDK14.2->15.2, and SD 5.1->6.1
I'm calling sd_flash_write() and sd_flash_page_erase() before enabling the SoftDevice with...
Hi,
I start a new design using the nRF Connect Sdk instead of the nRF5 Mesh Sdk.
Is it possible to provision a device over the mesh network using the NCS (like the PB...
After LPN publishes message, NRF_MESH_EVT_LPN_FRIEND_POLL_COMPLETE event is generated five times. Also I noticed that instead of transmitting single publication message LPN...
Hi,
We have a problem with a nrf9160 connected in NB-IOT with a bad signal.
During the debugging session to try to figure out what happen, we saw that the mqtt_evt_handler...
Hi everyone,
I have a problem since a couple of day with an interrupt of app_timer not triggering when adding a BLE central to my project. The device is working well as...
If I can get time through WiFi then send it to the nRF5340 and place it in a Struct TM. is there any method to have the nRF5340 maintain the time/calendar from that initial...
I'm sorry. This must be trivial to all of you. I'm a beginner with nrf52 programming, and I saw several examples that refer to timers TASK_START, TASK_CLEAR, TASK_STOP. Everywhere...
