Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Optimization level is set to "Debug". Tried to change it to one of the Levels, however then firmware does not run at all. Debugging Level is set to Level 3.
Can it be other...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
Hi! I'm working on a custom board with nRF9160, I want to flash it with the asset tracker sample, however, I do not own a J-link device. What I have is a FTDI USB-UART converter...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
