Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello, I am currently trying to build the lwm2m_client sample on my nrf9160DK but I am facing these issues in my Kconfig file, specifically with the BSD_LIBRARY dependency...
Hi,
I noticed (as highlighted in screenshot below) some of the IP based BLE projects under “Experimental: IoT Examples” found in all previous versions of nRF5 SDK that I...
Hi
We've recently added FreeRTOS to the firmware of an existing product (primarily to pre-empt big chunks of 3rd-party code over which we have no control and execute them...
Hi,
As discussed, the instructed PCB land pattern for nRF9160 is according to Product Specification:
However, we have noticed that land pattern exceeds nRF9160 dimensions...
Hello ,
I am trying DFU over BLE.I am using SDK 14.0.2 .
i Flashed Bootloader Code and Softdevice 5.0.0 .then Device is Starting Advertised as DfuTarg and As Mention in...
Hello,
i have one nrf52840 board with a coded phy scanner and another sending advertisings, when it are close , i received in the scanner 100% of Advertisings, but when...
Hello,
I'm doing some initial investigation with the nrf9160 DK and after some reading and testing, it's clear that significant part of the low-power capabilities is determined...
Hi, I'm using nRF52 DK (nRF52832), demo code <TWI sensor>. I'm using this slave sensor to communicate with Master nRF52 DK. My code gets stuck at sensor_set_mode() function...
Hi,
I am trying to test the eligibility of updating my project from SDK 16.0 to 17.2 using DFU. I programmed just softdevice and bootloader of SDK 16.0 and made a package...
Hello All ,
I want to use timer 2 of nRF52810..my code is not giving any error but timer is also not going to IRQ handler...but if i made the same changes for timer 0 it...
Hello,
I'm using Seeger Embedded Studio and S132.
I'm trying to include ble_nus.h to ble_app template and compiling. But it gives this error:
2> In file included from...
hi,
I have following setup test cases .
Case 1 DK2 , DK1 Initialized with CLI directly
1a DK2 , DK1 Directly connected to CLI Every Thing Works
1b DK2-to-DK1-to-CLI...
Hi,
I am checking the voltage range on the input pins of the Nrf52832. The specs show VIH is 0,7*VDD and VIL is 0,3*VDD. I'm using the Nrf52DK, which has about 2.8V VDD...
Hello again,
This time I am trying to read HID reports using bluetooth to get the state of the caps lock.
I know this should be super simple and its explained in the hid...
