Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
I built this ( devzone.nordicsemi.com/.../Nordic_2D00_Thingy52_2D00_FW_2D00_master.zip) Nordic Thingy SES project and downloaded the generated hex file in Nordic Thingy. Now...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
Hello,
I have recently built and flashed CoAP Sample on my board.
After that the device cannot connect to the mobile network.
Could you please provide me a description...
Hello,
We have finished the development of a prototype device that incorperates the nRF9160 SiP. I would like to know if there is anything I need to set-up in the device...
Hi,
I would like to use hal_time_get() [hal_timer.h] in my project, and I try to add below library into Makefile.
but I got an error. "error: implicit declaration of function...
i am using/ ble_app_multilink/ example present in central folder..i am beginner to this ,,so i have few doubts in it
1)so where actually advertisers(which are advertising...
