Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
We are using nRF52840 with BLE and 802.15.4 concurrent with S140 SoftDevice. There are two functions to set the transmit power for each radio protocol:
sd_ble_gap_tx_power_set...
Hi all!
In my application I would like to use LESC OOB pairing between two S132 SoftDevices. But there is one thing that I'm not sure of: I only have the (wired) OOB channel...
Thank you for considering my problem!
I have maybe have seen a working Micro SD card with the 52840DK, but have not been able to produce it on my board. 52832. I am using...
I understand that the nrf9160 product is still in pre-release. I did have a look at the gps receiver section in the DocLib.
For future planning it would be very helpful...
I am setting up a custom hid device bulk transmission, which can normally send data to PC at present, but cannot receive data from PC (no data interrupt was received in the...
I am able to use the 2 channel mode of each PWM giving me a total of six PWM that I can set individual duty cycle PWM!
I now find I need 8 PWM with individual duty cycles...
I see that BBC Micro:bit uses nrf51822 and can use RADIO peripheral.
So I tried to make my nrf52832 DK to talk to Micro:bit by using Gazell library and referencing MicroBitRadio...
Hi,
We are using SDK14.2.0 and getting assertion failed error with id = 1, pc = 0xEAC2 and info = 0.
What can be the cause of this error?
Thank you in advanced.
The function model_timer_elapsed_ticks_get() returns the total number of ticks since the timer was started. Hence it's expected that this function to return a value > 0 when...
I am attempting to do the LTE_Gateway example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for the...
Dear All,
I am using NRF52840 DK with SDK13.0 . I am trying to use one SAADC channel (CH 1) to record input signals at 200 kHz to fill a buffer of 2000 points . After the...
Hi
I was playing around with the new SDK 15.3.0 and most things worked as expected. One thing that causes some trouble is the changed MBR parameter page handling. It seems...
i need to generate an irk from nrf52 so that no device can identify that nrf52 data...only the device with same irk can identify and connect to it
for that what should i...
I am trying to port Keil code to SES 3.40 with NRF51822 Device and SDKV12_3, I am currently using the ble_app_uart example. I followed this blog post https://devzone.nordicsemi...
