I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello,
Our board is based on nRF52832 with S132 5.1.0, without RTOS. Now we have a requirement to protect sensitive memory areas with MPU, so I'm trying to run firmware...
Hi,
I am using nrf 52840 development board for developing mesh. I am using segger IDE in my windows 7 desktop for code flash to the board.
The SDK I am using is nRF5_SDK_15...
Hello to everyone.
I have a doubt about the function of NRF_LOG library in nRF52 DK. I´m trying to display the voltaje value from pin P0.26 on Termite, so I saw in this...
I have a eval board pca10040 and a custom board both having nrf52832 chip, on the eval board the nrf_sdh_enable_request function calls happens successfully with error code...
Hi Folks,
I am trying to get some data to persist past a reboot. I noticed the ram_retention_pca1004 example and it showed a simple assignment of:
NRF_POWER->GPREGRET...
Using SDK15.2 example ble_app_hrs, i need to transfer custom messages and values to the phone app so i want to use ble_nus service, i did everything as in the example ble_app_uart...
This PAN states:
"Conditions • GPIOTE is configured in event mode • TWIM/SPIM utilizes EasyDMA"
What is not completely clear are these two separate conditions? Or do both...
Hi,
I am using the 2 NRF52840 boards, rev 1. I am using SDK 15.2. The first board is running the NRFX_SPIM example. The second board is running the SPIS example. The rx_delay...
Hi,
I am trying to combine TWI and SPI peripherals to the ble_app_uart exmaple in SDK 15.2
I am facing the following error
.\_build\nrf52840_xxaa.axf: Error: L6200E...
Hi,
I'm exploring the HID keybaord example of nrf5 SDK V12.3.0, and get a problem:
I first connect my iphone to the device, and it's working, if the device is 'ignored...
I am working on a linux vm 16.04 and playing with the pc-ble-drive-js library. I recently got the board up and running and started looking at the heart_rate_collector example...
Hi,
without providing too much code right away, I would like to ask how I could circumvent AT command interface hangups. My current test application calls AT commands like...
Hi there,
I'm looking forward to improve our firmware in terms of power consumption. Therefore we would like to use Power Debugging mechanism which is support by IAR Workbench...
The example projects I am referring to is located here:
nRF5_SDK_15.2.0\examples\iot\mqtt\lwip\subscriber\pca10056\s140\ses\iot_lwip_mqtt_subscriber_pca10056_s140
nRF5_SDK_15...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
