Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
Hi dear nordic employee:
I use blew：
chip：nrf52832 CIAA-B00
SDK: 12.3.0
what‘s I want is same as this ， when the interrupt happen，I want to know the toggle is HIGH_TO_LOW...
Hi,
I want to develop a 4 Chanel Wireless audio system
I am using an EEPROM (without MC) to configure the nRF24.
I want to split the available band (2,4GHz to 2.5 GHz...
Hi,
I have the problem, that nrf_crypto_init() does not find any backends and thus is skipping the initialization.
What is the precondition for NRF_CRYPTO_BACKEND_SECTION_ITEM_COUNT...
Hello,
after migrating to SDK15 we noticed, that our spi master seems to clock out single bytes instead of a continous clock for the whole transfer.
The Migration guide...
Hi
I want to update bootloader.zip file over BLE DFU mode without signature checking , the open bootloader example only for USB,
How to disable bootloader signature checking...
when message relay by any node how can other node know that it is for him and update status.
for example if I subscribe some nodes to 0xc001 group and others to 0xc002 group...
Hello,
I am making a PCB for my project using the nRF51822 chip? Can I power a LED with the GPIO pin or do I need to connect a MOSFET to drive the current? Also, I want...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
hi,
I'm trying to merge the the proxy server and beaconing example together. When I compare two main.c and copy the advertising part from beaconing to proxy server example...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
Hi Sir
I'd want to send DTM command by hard code, but I don't know where is the command spec for reference ?
Has any one could show me where is the spec ? and give me...
Hi,
I am using nrf52832 with soft device 3. I am operating on peripheral role, while i am initiating sd_ble_gattc_exchange_mtu_request with desired MTU ,it internally sends...
Hi! I am using SDK15.0 and SD 132 v6.0.0. My IDE is Segger Embedded Studio.
Everything was working fine and then suddenly after few weeks of developing a problem appeared...
