Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hey guys, for testing purposes on nrf52833 and SDK 2.8.0 I want to use a simulation and stumbled upon bsim . I followed the instructions there and can build and run the hello...
I encounter this problem:
The radio_test application works correctly on the official nrf52840dk board, but cannot receive input commands on my custom product board.
However...
Hi,
I have been developing a PCB with an nRF9151 and a SKY65943-11 LNA among other ICs. I looked up the nRF9151 Development Kit (PCA10171) datasheet for some of the pinouts...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
we used SDK V2.6.2,
we used external flash for the OTA,
when we do the OTA after the NVS flash is erase so how we can solve this,
we used nvs_storage for this,
EMPTY_0...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
We are developing a system were we rely heavily on the use of LWM2M. Using the provided LWM2M client we normally dont experience any problems at all and are able to establish...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
We have the Watchdog on the 5340 running but when we enter the software updater we wish to dissable it.
We have the following code to disable it but we are seeing the watchdog...
