Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I want to add wdt function in ble_app_uart. Please tell me where should I feed the wdt.
in below main loop?
for (;;)
{
power_manage();
nrf_drv_wdt_channel_feed(m_channel_id...
I'm trying to decide the best way to be able to have sub millisecond time keeping, but keep the processor sleeping until it gets a hardware interrupt.
Basically I need...
Hello Nordics Developer
I'm from indonesia, i'm electronics designer, i have develop new products using BLE, first develop i'm using nrf51 series but And my boss ask is there...
I'm trying to conserve space in the advertising packet, and would like to free up the space used by the 128 bit (16 byte) service item list, as this takes a minimum of 18...
Hello all,
I am working on nrf51 series for mesh application so regarding Pre addressing of controller how will get to know the adresses of SOC's in mesh network?
can...
I am using the nRF51822 with the s130 softdevice, and I would like to control three RGB LED modules with three PWMs (R, G, and B). For various conditions, either one, two...
[CONDITION]
1. R1 = 1.5M, R2 = 430K
2. GAIN = 1/2
3. RESOLUTION = 10bits
4. Single End
[ISSUE DESCRIPTION]
1. If voltage is changed by 0.1V step (4.1V -> 4.0V), the...
Hello
I wanted to ask what is the correct way to use NRF_LOG_* functions along with printf (with RETARGET_ENABLED 1 ) and normal UART initialized with standard:
const...
Hi all,
I have some problem with the FDS write function.
This is some example codes for my FDS write:
// Global variables
static uint16_t fileID;
static uint16_t...
Hello, I am going over this example here:
infocenter.nordicsemi.com/index.jsp
I am a bit confused how this works. My intention is to create a slave, so a master can send...
Trying to get the BMD-200 board up and running and the blinky_pca10028.hex seems to work just fine but compiling it from source (blinky/pca10028/blank/armgcc)does not. There...
Hi I am using gcc based environment for flashing the nrf52840 SDK with BLE applications. I tried to modify one of the applications to send SPI data received from non-nordic...
I am using sdk12.3 with NRF51822 and the original ANCS project. It can successfully bond with iPhone ,but the bonding only takes place at the first time after the firmware...
