I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello!
I'm trying to get the 16 bit ADC value as 2 of 8 bit array from nRF51 development kit over bluetooth to MCP, but when it displays on the MCP the value is "swap"...
Is it a good idea to use nRF51 standalone as an Application Processor and also as BLE connectivity chip?
OR
Is it a good practice to use a separate Application Processor...
I have a question on - to me - seemingly weird behavior about copying data out of the event from the soft device.
Situation: I have a 32 bit integer characteristic which...
Hey all!
Newbie here. I developed and tested some code on an NRF51DK easily enough using mbed, and now I'm trying to put it onto a PTR5518 module from Xuntong (which I...
Could you rub my nose in Bluetooth SIG Core or just explain what does chip do when switching to very noisy channel? For example Wi-Fi working very close to our device.
Hello:
I have read the documentation but I cannot determine if INPTR and OUTPTR can be set to the same memory address? I will try it to see what happens but it would be...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Everyone,
I found out on that ble_app_power_profiling application is developed for Lower power current consumption....as It keeps system in the system_off_mode until...
Hi,
I am trying to measure and minimize current consumption .....
Following previous question on this forum,I found way to measure current on NRF51 DK by cutting SB9....
Hello Everyone..
i am new to nrf52 and this community.
i am using nrf52 and android master control pannel.
in my code i define my custom uuid base to ..
//430Cxxxx...
Hi, I'm looking for an easy way to use the UART in blocking mode (or something similiar) with a receive buffer that is filled in background:
If possible using EasyDMA...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everybody
I am making a custom board which using ANCS (nrf51 sdk 9.0.0, softdevice 110 ver8.0.0). I saw on the original code have button_led_init() function to initiate...
hello,
I've encountered a problem with our own nrf51822 circuit not advertising.
Our circuit is exactly the same as what is given as the reference circuitry on the datasheet...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
