Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I'm trying out to operate an external flash and first thing to try before anything was the spi_flash sample.
*** Booting nRF Connect SDK v2.8.0-a2386bfc8401 *** *** Using...
I have a question about tasks with different priorities and interrupts.
So for example I am using I2C and UART with different tasks and suppose I2C is in the midst of transaction...
Hi all,
We are working on a project that uses the nRF5340 and nRF7002 combo. In our application, the device enters a low-power mode on the nRF5340 during sleep, with the...
Hi,
As the subject, when i connect to the Windows with the cable connected with VDD side, it will not show up Jlink in Windows.
What should I do to reset the Nrf5340 ...
Hey everyone, I am looking for big size capacitive touchscreen for my next project so I do found with resisitve touch using FT810 EVE graphic controller with nrf52840( https...
I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248.
In VSCode with the NRF plugin I select "Add build configuration...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
I'm using the nRF54L15-DK to run a Bluetooth peripheral_hr project in DCDC mode, but if I write
nrf_regulators_vreg_enable_set(NRF_REGULATORS, NRF_REGULATORS_VREG_MAIN,...
Context: I am working on a project to monitor up to 880 devices in an Industry 4.0 warehouse. The warehouse is divided into 16 areas, with each area housing 30–55 devices...
Hi everyone,
I’m a complete beginner and need some help. I’m working with two XIAO nRF52840 Sense boards: one as a central and the other as a peripheral. My goal is to send...
Hi,
I am trying to use a digital channel to sync with a current measurement. I have connected VCC, GND and a digital output of my DUT to the PPK2. I can see from the scope...
