I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
We are trying to attain power optimization in our project, which uses the nRF5340 board. In our code we have implimented RTOS, BLE for data transfer and are using i2c...
Hi,
I encountered an issue since i upgraded nrfjrpog
My previous version was 10.13.0
And now is 10.24.2.
I have a batch file to program my device and until the upgrade...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...
Hi team,
We tested the nRF7002 with the nRF5340 as the host. Now, our application needs to connect the nRF7002 Wi-Fi module with a custom microcontroller other than Nordic...
Hello,
I am trying to establish communication between the nRF9160 SoC and the nRF52840 on the Thingy:91. I have two arrays: one of 774 bytes and another of 8 bytes. Currently...
In the Wi-Fi Fundamentals Course, Lesson 2, Exercise 2 (step 7.2) I found that it is necessary to clear the bssid parameter in the wifi_connect_req_params structure. If it...
Message:
Hi Nordic Semiconductor Dev Zone,
I am developing a PCB that mirrors the one in Sony WF-1000XM5 earbuds, but with the microcontroller replaced by the nRF9161...
I use NRF52832 as a Bluetooth gateway to receive commands and initiate connections to devices. Each instruction received will be interrupted through the IO pin, and the MAC...
OS: Window11
Programmer version : v4.4.0
Used Chip: nRF5340
Used Hex file: peripheral_uart_nrf5340dk.hex
An error occurred while Erase&Write the Hex file while testing...
The default setting for the external flash chip of 9160dk appears to be 64m, but when used, the log display only shows 8m, and only the part within 8m can be used,
Then...
