Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We're developing an LwM2M application based on the lwm2m client sample with the goal of sending data to ThingsBoard as our main telemetry platform.
The Application in based...
Greetings, Our system consists of three BLE sensors using an nRF52840 to send data back to a central tablet or PC. We are receiving reports that the sensors take a long time...
I've been searching threads on this topic on DevZone and I found a couple that concluded that MCUBoot can work with external SPI flashes, but not with an SD card.
Is that...
I am using PHYTEC link board eth ( https://docs.zephyrproject.org/latest/boards/shields/link_board_eth/doc/index.html ) as ethernet shield using SPI on nRF9161.
I updated...
Hello, per the PPK2 user guide, I see that the switching during auto-ranging can cause measured current to be higher than the actual current due to inductance.
To be clear...
Our products use NRF52832 chips in production, and now the finished product needs to do an SRRC certification, but I need to confirm whether the original factory of this chip...
Hey, I need to set characteristic length for a PTS test to MTU-1 Otherwise the test case GATT/SR/GAC/BV-01-C will failed with the message - Failed: Cannot find characteristic...
hello:
My project is based on "esb_rx",NCS2.5.1，nRF52832.I need a Unique address for my product ,so I add flash read/write function for my projict, base on "soc_flash_nrf...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
